Характеристики и описание
Описание оборудования | |
|---|---|
| Thru-beam sensor SET | |
System components | |
| Emitter | OBE40M-R201-S-IO-0,3M-V1-L |
| Receiver | OBE40M-R201-2EP-IO-0,3M-V1-L |
General specifications | |
| Effective detection range | 0 ... 40 m |
| Threshold detection range | 50 m |
| Light source | laser diode |
| Light type | modulated visible red light |
| Laser nominal ratings | |
| Alignment aid | LED red (in receiver lens) illuminated constantly: beam is interrupted, flashes: reaching switching point, off: sufficient stability control |
| Diameter of the light spot | approx. 80 mm at a distance of 40 m |
| Angle of divergence | approx. 0.12 ° |
| Ambient light limit | EN 60947-5-2 : 40000 Lux |
Functional safety related parameters | |
| MTTFd | 440 a |
| Mission Time (TM) | 20 a |
| Diagnostic Coverage (DC) | 60 % |
Indicators/operating means | |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Function indicator | Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4Hz) - insufficient operating reserve |
| Control elements | Receiver: light/dark switch |
| Control elements | Receiver: sensitivity adjustment |
Electrical specifications | |
| Operating voltage | 10 ... 30 V DC |
| Ripple | max. 10 % |
| No-load supply current | Emitter: ? 13 mA Receiver: ? 15 mA at 24 V Operating voltage |
| Protection class | III |
Interface | |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| Device profile | Identification and diagnosis Smart Sensor: Receiver: type 2.4 Emitter: - |
| Transfer rate | COM2 (38.4 kBaud) |
| IO-Link Revision | 1.1 |
| Min. cycle time | 2.3 ms |
| Process data witdh | Emitter: Process data input: 0 bit Process data output: 1 bit Receiver: Process data input: 2 bit Process data output: 2 bit |
| SIO mode support | yes |
| Device ID | Emitter: 0x111412 (1119250) Receiver: 0x111312 (1118994) |
| Compatible master port type | A |
Input | |
| Test input | emitter deactivation at +UB |
Output | |
| Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link /Q - Pin2: NPN normally closed / light-on, PNP normally open / dark-on |
| Signal output | 2 push-pull (4 in 1)outputs, short-circuit protected, reverse polarity protected, overvoltage protected |
| Switching voltage | max. 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Usage category | DC-12 and DC-13 |
| Voltage drop | ? 1.5 V DC |
| Switching frequency | 1250 Hz |
| Response time | 0.4 ms |
Conformity | |
| Communication interface | IEC 611 |
Описание оборудования
Laser thru-beam sensor OBE40M-R201-S2EP-IO-0,3M-V1-L
Под заказ
Цену уточняйте
Минск ∙
Доставка
Оплата и гарантии