Характеристики и описание
Описание оборудования | |
|---|---|
| G2 flat module 4 inputs and 2electronic outputs | |
General specifications | |
| Slave type | A/B slave |
| AS-Interface specification | V2.1 |
| Required master specification | ? V2.1 |
| UL File Number | E223772 |
Indicators/operating means | |
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of outputs |
| LED PWR | AS-Interface voltage; LED green |
| LED AUX | ext. auxiliary voltage UAUX ; LED green |
| LED IN | switching state (input); 4 LED yellow |
| LED OUT | Switching state (output); 2 LED yellow |
Electrical specifications | |
| Auxiliary voltage (output) | 20 ... 30 V DC PELV |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| Rated operating current | ? 30 mA |
| Protection class | III |
| Current loading capacity | 2 A (IAUX) |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) |
Input | |
| Number/Type | 4 inputs for mechanical contacts or 3-wire sensors (PNP), DC |
| Supply | from external auxiliary voltage UAUX |
| Input current | 3 mA (typically) |
| Switching point | according to DIN EN 61131-2 (type 1) |
| Signal delay | < 2 ms (input/AS-Interface) |
| Signal frequency | ? 250 Hz |
Output | |
| Number/Type | 2 electronic outputs, PNP, overload and short-circuit proof |
| Supply | from external auxiliary voltage UAUX |
| Current | 1 A per output , 2 A per module |
| Voltage | ? (UAUX - 0.5 V) |
| Usage category | DC-13 |
Galvanic isolation | |
| Input/Output | none |
| Input/AS-Interface | Basic insulation, rated insulation voltage120VDC |
| Output/AS-Interface | Basic insulation, rated insulation voltage120VDC |
Directive conformity | |
| Electromagnetic compatibility | observe notices on the certificate of conformity. |
Standard conformity | |
| Galvanic isolation | EN 60947-1:2007 |
| Degree of protection | EN60529:2000 |
| Mech. capacity | EN60068-2-6:2008, EN60068-2-27:1995 |
| Input | EN 61131-2:2007 |
| Usage category | EN60947-5-1:2005 |
| Emitted interference | EN61000-6-4:2001 |
| AS-Interface | EN62026-2:2013 |
| Noise immunity | EN 61326-1:2006 |
Programming instructions | |
| Profile | S-7.A.E |
| IO code | 7 |
| ID code | A |
| ID1 code | 7 |
| ID2 code | E |
| Data bits (function via AS-Interface) | input output |
| Parameter bits (programmable via AS-i) | function |
Ambient conditions | |
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Relative humidity | 85 % , noncondensing |
| Climatic conditions | For indoor use only |
| Altitude | ? 2000 m above MSL |
| Pollution degree | 3 |
Mechanical specifications | |
| Degree of protection | IP67 |
| Connection | Cable piercing method flat cable yellow/flat cable black inputs/outputs: M12 round connector |
| Material | |
| Mass | approx. 100 g |
| Tightening torque, cable gland | 0.4 Nm |
| Mounting | Mounting plate |
Описание оборудования
По вопросу интересующей Вас продукции, пожалуйста, свяжитесь с нами:
8 (029) 555-8-000 | |
8 (044) 555-8-000 | |
8 (017) 255-8-000 |
Или отправьте нам запрос на e-mail: zapros@filfar.by
AS-Interface sensor/actuator module VBA-4E2A-G2-XE/E2
Под заказ
Цену уточняйте
Минск ∙
Доставка
Оплата и гарантии